PRECAST GIRDER ERECTION · SPAN ADVANCEMENT · BRIDGE CONSTRUCTION

Launching Gantry Crane for Bridge Building

Place precast girders on bridge supports and advance the erection equipment along the alignment.

A launching gantry crane combines lifting equipment with a structure that changes support positions as construction progresses. Girder erection, trolley travel, launching and support transfer are designed as one coordinated system.

Henan Mine Crane prepares launching gantry proposals around your bridge drawings and erection method. Receive the equipment arrangement, lifting specification, support reactions and an itemized supply scope, with installation and commissioning services defined in the offer.

Equipment and Engineering in One Proposal

The launcher matched to the erection method

The proposed main structure, lifting units, supports and advancing system follow the way the bridge will be built. Complete-girder erection and segmental construction receive different equipment arrangements.

Bridge interfaces shown on the drawings

Support locations, bearing footprints, clearance envelopes and construction-stage reactions are identified for coordination with the bridge designer. This gives the civil and erection teams a common set of equipment interfaces.

Controls linked to the permitted movements

The control scope defines lifting, trolley travel, support adjustment and launching modes. Specified interlocks and monitoring functions follow the agreed sequence and fault-response requirements.

A defined route to site handover

The offer brings together fabrication, inspection, transport sections, assembly documentation and contracted site support. Operating instructions, maintenance information and recommended spares form part of the agreed handover package.

Technical Specification for Your Bridge

The technical offer states the machine’s rated performance and permitted operating conditions. Its drawings cover both the suspended load and the equipment’s changing support arrangement.

Technical item Included in the project specification
Rated erection load Total suspended load and the permissible load at each lifting unit.
Girder and lifting-device geometry Girder length, depth, center of gravity, lifting-point spacing and lifting-beam interfaces.
Bridge span and machine arrangement Permitted support spacing, launching geometry, overall equipment dimensions and working clearances.
Hoisting system Hook travel, rated lifting speeds, lifting-unit arrangement, braking and specified coordination functions.
Launching and support transfer Advancing mechanism, support positions, temporary conditions and the permitted sequence.
Alignment envelope Approved skew, curve radius, longitudinal gradient and crossfall for the selected arrangement.
Bridge support reactions Reaction schedules for the relevant erection, advancing, support-transfer and parking states.
Controls and protection Operating stations, load and position monitoring, travel limits, interlocks and fault response.
Power and site interfaces Supply voltage, frequency, installed load and any specified generating equipment.
Wind and out-of-service condition Operating limits, securing arrangements and the specified parked configuration.
Inspection and acceptance Agreed inspections, functional tests, proof testing and trial-launch acceptance records.

Each supplied configuration has its own approved load and geometry envelope. Capacity, bridge span and available hook travel are specified together; a larger lifting rating alone does not establish suitability for a longer or more curved bridge.

Choose the Launching Arrangement Around the Bridge Method

Construction method Equipment arrangement Main project interface
Complete precast girders A beam launcher picks up and places individual girders. Girder delivery, lifting points, placement range and pier-to-pier advancement.
Span-by-span segmental erection A launching gantry handles or supports the precast segments forming a span. Segment delivery, suspension, alignment and the approved stressing and load-transfer sequence.
Balanced-cantilever segmental erection An erection arrangement serves the defined sequence around a pier. Pier support, segment placement order and construction-stage balance.
Full-span heavy box girders A full-span erection system handles the complete heavy element. Transporter interaction, deck reactions, support geometry and launching stability.

The arrangement is selected for the specified construction method. Functions for a different method are engineered separately rather than assumed to be available on the same machine.

Select the Launcher from the Load and Construction Sequence

Complete suspended load and individual lifting points

Girder weight is combined with the lifting beam, slings, clutches and other carried equipment. The lifting-point locations and center of gravity establish the demand on each lifting unit. Equal sharing is not assumed simply because two hoists are fitted.

The full bridge alignment

The equipment layout follows pier spacing, skew, curvature, gradients, crossfall and the first and last span conditions. Girder delivery and placement are checked against the same geometry, including edge-girder positions and changes along the route.

Launching states as well as lifting states

The structural and stability assessment covers the machine while it advances and transfers between supports. These temporary states can govern the design even when no girder is suspended. Assembly access and the final dismantling route are included in project planning.

Launching Gantry Compared with Beam-Yard Equipment

Equipment Main function Support and movement
Launching gantry crane Erect girders or segments along the bridge alignment. Uses the designed bridge or temporary support arrangement and advances through an approved sequence.
Construction gantry crane Lift components within a construction work area. Travels along a defined ground runway; lifting coverage follows the rail layout.
Double-trolley truss gantry crane Handle long components at two lifting positions. Provides a rail-served yard lifting platform with engineered individual or coordinated operation.
Precast concrete straddle carrier Lift and transport components between yard locations. Travels on a suitable pavement route with the required load clearance and steering space.

A Coordinated Girder Erection and Launching Cycle

Stage Equipment function
Girder delivery Receive the girder at the specified pickup position from the deck transporter or other approved feeding arrangement.
Pickup and transfer Lift at the approved points and move within the permitted load and travel envelope.
Placement and load release Position the girder on the designed supports and transfer its load through the approved erection sequence.
Preparation to advance Establish the specified support, trolley and equipment positions for launching.
Span advancement Advance to the next working position, transfer supports and verify the required conditions before the next erection cycle.

Protection tied to the operating mode

The specified control system can include load indication, hoist coordination, travel limits, support-status monitoring and interlocks between incompatible movements. The engineering documents define the response to power loss, a control fault or an interrupted movement.

Commissioning verifies the supplied functions against the approved sequence. Site operation follows the machine’s operating instructions and the project erection method statement.

Capacity Planning Example: A 120 t Precast Girder

For an illustrative girder-handling arrangement, the static suspended load is calculated as follows:

Load item Illustrative weight
Precast girder 120 t
Lifting beam, rigging and carried lifting equipment 10 t
Combined static suspended load 130 t

A nominal 160 t launcher may be considered as an initial candidate. Final selection also checks individual hoist loads, design load combinations, allowable lifting positions, bridge geometry and launching states. This arithmetic alone does not approve a lifting arrangement or set a universal capacity margin.

Launching Gantry Crane Prices

For the conventional 100–200 t girder-launching configurations below, allow an approximate EXW equipment budget of US$180,000–410,000 per set.

Nominal launcher capacity Approximate equipment price, USD / set
100 t US$180,000–240,000
160 t ;">US$240,000–310,000
200 t US$330,000–410,000

The final price follows the complete girder load, bridge geometry, support and advancing arrangement, controls and supply scope. Freight, import charges, bridge or temporary works, installation and commissioning are separately priced.

Heavy full-span systems, segmental erection gantries and special curved or variable-span arrangements are quoted for the engineered project configuration.

Get a Launching Gantry Price

Connect Beam-Yard Handling with the Erection Front

A launcher depends on a reliable supply of completed girders. Henan Mine Crane can coordinate beam-yard gantries and mobile precast carriers with the transporter pickup arrangement, storage supports and delivery sequence.

Henan Mine Crane engineering gantry crane for construction and beam-yard handling
Construction gantry equipment for component staging and loading within a rail-served work area.
Henan Mine Crane precast concrete carrier for yard lifting and transport
Mobile precast carrier for yard pickup, transport and placement before delivery to the erection front.

The yard layout and erection plan identify the handover points, component orientation and lifting-device interfaces. This allows the storage, transport and erection teams to work from a coordinated handling route.

Manufacture, Installation and Handover

Project stage Deliverable
Technical proposal Equipment arrangement, principal specifications, preliminary interfaces and itemized commercial scope.
Engineering approval General arrangement, operating envelope, load and reaction schedules, erection and launching sequence, and control requirements.
Manufacture and inspection Agreed material and manufacturing records, inspection points and factory test documentation.
Site assembly and commissioning Assembly documentation, contracted supervision or installation support, and agreed functional, load and trial-launch verification.
Operational handover Operating and maintenance manuals, electrical and hydraulic drawings as applicable, component identification, training and recommended spares within the order scope.

The commercial offer identifies delivery milestones, shipment terms, site responsibilities, acceptance criteria and warranty coverage. Inspection records and any customer witness requirements are agreed before manufacture.

Launching Gantry Crane FAQs

What is a launching gantry crane for bridge building?

It is specialized erection equipment that places precast girders or segments and advances along the bridge alignment through a designed support sequence. Its engineering covers both lifting operations and the temporary states involved in launching.

Is a beam launcher the same as a segmental launching gantry?

A beam launcher normally places complete precast girders. A segmental launching gantry handles or supports the segments used to form a span or cantilever. The lifting, support and load-transfer arrangements depend on the construction method.

Can a launching gantry work on a curved or skew bridge?

A suitable arrangement can be engineered for defined curvature, skew and gradients. The permitted alignment envelope, support positions and girder placement range are stated in the approved project design.

How is the required lifting capacity calculated?

The calculation includes the girder or segment plus the lifting beam, rigging and other carried equipment. Individual lifting-point reactions, design load combinations and permitted operating positions are assessed before the equipment rating is selected.

Why are bridge support reactions part of the quotation?

The launcher transfers loads into the bridge or temporary works. Reactions change during lifting, advancing, support transfer and parking, so the bridge designer needs the relevant load cases and support locations.

Can a conventional beam-yard gantry replace a launcher?

A beam-yard gantry is designed to lift within its runway or prepared travel area. Pier-to-pier erection and launching require a different support and advancement design. The two equipment types can serve separate stages of the same project.

How much does a launching gantry crane cost?

The listed conventional 100–200 t girder launchers have approximate EXW equipment budgets of US$180,000–410,000 per set. Bridge geometry, launching arrangement, controls and contracted services determine the final quotation.

What can be included with the launching gantry supply?

The agreed package can include equipment, engineering drawings, reaction schedules, control documentation, inspection records, assembly instructions, installation support, commissioning, operator training and recommended spares. Included and separately priced items are identified in the offer.

Request a Launching Gantry Crane Proposal

Plan girder delivery, bridge erection and span advancement with an equipment proposal from Henan Mine Crane.

Receive a proposed launching arrangement, technical scope, bridge-interface requirements and itemized quotation. Installation support, inspection, commissioning and handover services are identified alongside the equipment.

Send the bridge general arrangement, girder weight and lifting-point drawing, span schedule and intended erection method. Include the project location and target installation date to begin the proposal.

Email: info@hnksglobal.com

Get your customized solution
Contact us today by email at info@hnksglobal.com or fill out the form below.



    X